Origin of visible photoluminescence from porous silicon as studied by Raman spectroscopy

In this paper we discuss the different models proposed to explain the visible luminescence in porous silicon (PS). We review our recent photoluminescence and Raman studies on PS as a function of different preparation conditions and isochronal thermal annealing. Our results can be explained by a hybrid model which incorporates both nanostructures for quantum confinement and silicon complexes (such as SiH _x and siloxene) and defects at Si/SiO₂ interfaces as luminescent centres.     

氢化非晶硅磷掺杂工艺条件的研究

本文对氧化非晶硅磷掺杂的工艺条件进行了研究，得出掺磷氢化非晶硅的电导率随衬底温度、气体流量、气体压力、射频功率、淀积时间的变化关系，为非晶硅的有效掺杂和器件研究提供了依据。     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.     

顺丁橡胶生产过程"门尼升值"的原因研究

研究了顺丁橡胶生产过程中门尼升值的原因。结果表明，顺丁橡胶生产后处理的膨胀干燥过程存在门尼升值现象。不同内在质量的顺丁橡胶门尼升值不同，正常条件下门尼升值发生于门尼粘度的测试过程。     

树脂热解炭制备碳化硅晶须

用自制的配合醛树脂热解和炭源，用ＳＩＯ２超细汾作原，根据碳热还原原理，利用常规加热和微波加热两种方式，分别制备了直径在纳米级的ＳｉＣ晶须，Ｘ射线衍射、透射电检测结果表明：制备工艺和条件对ＳｉＣ晶须的性质有较大的影响。     

驻极体声传感器及其储电材料的现状

综述了驻极体声传感器及其储电材料近年来的迅猛发展。传统的FEP(tetrafluoroethylene—hexa—fluoropropylene copolymer)极体电容式声传感器及以铁电聚合物PVDF(poly vinylidene fluoride)家族为芯片的声传感器和超声抉能器仍焕发着青春活力。Si基微型驻极体声传感器的理论和实验研究已经日趋成熟，而用空间电荷型多孔聚合物驻极体压电薄膜为芯片可望研制出新一代声电和电声传感器、压力传感器和驱动器。     

Oxidation of Silicon Carbide in Environments Containing Potassium Salt Vapor

At high temperatures in clean oxidizing environments, SiC forms a very protective SiO₂ film, but, in environments containing low levels of gaseous alkali salt contaminants or where condensed salts may deposit on the surface, the resistance of the film is significantly reduced. Oxidation kinetics of SiC were measured by continuous thermogravimetric analysis in a controlled environment containing CO₂, H₂O, and O₂ plus low levels of potassium-containing salts. Potassium was found to be incorporated into the SiO₂ scale and to significantly change its transport properties and its morphology. The rate of scale formation was found to increase directly in proportion to K in the scale. A change in mechanism was observed when water vapor was added to the reacting gas stream.     

Nuclear Magnetic Resonance Studies of Silicon Carbide Polytypes

The ²⁹Si MAS NMR spectra of the 2H, 4H, 6H, and 3C polytypes of silicon carbide are presented. An attempt is made to correlate differences in the chemical shifts with local atomic environment. The results of the analysis of the spectra of pure polytypes are used as a basic for the interpretation of the spectra of mixed polytypes and a discussion of the crystallinity and impurity levels of different samples. Carbon-13 chemical shifts obtained from spectra of the same polytypes are also tabulated.     

A Silicon–Silica Nanocomposite Material

The synthesis and characterization of a novel silicon–silica nanocomposite material are reported. A self‐assembly method allows the encapsulation of silicon nanoclusters within the channels of a periodic mesoporous silica thin film. The result is the formation of a silicon–silica nanocomposite film with bright, room‐temperature photoluminescence in the visible range, and a nanosecond luminescence lifetime. The properties of the nanocomposite material have been studied by several analytical techniques, which collectively show the existence within the channels of non‐diamondoid‐structure‐type silicon nanoclusters with various hydrogenated silicon sites. It is estimated that the silicon nanoclusters in the silica mesoporous films occupy up to 39 % of the accessible pore volume. The nanocomposite film shows improved resistance to air oxidation compared to crystalline silicon. The high loading and chemical stability to oxidation under ambient conditions are important advantages in terms of the development of silicon‐based light‐emitting diodes from this class of materials.     

Stepwise-Graded Si3N4–SiC Ceramics with Improved Wear Properties

The processing of stepwise graded Si₃N₄/SiC ceramics by pressureless co-sintering is described. Here, SiC (high elastic modulus, high thermal expansion coefficient) forms the substrate and Si₃N₄ (low elastic modulus, low thermal expansion coefficient) forms the top contact surface, with a stepwise gradient in composition existing between the two over a depth of ∼1.7 mm. The resulting Si₃N₄ contact surface is fine-grained and dense, and it contains only 2 vol% yttrium aluminum garnet (YAG) additive. This graded ceramic shows resistance to cone-crack formation under Hertzian indentation, which is attributed to a combined effect of the elastic-modulus gradient and the compressive thermal-expansion-mismatch residual stress present at the contact surface. The presence of the residual stress is corroborated and quantified using Vickers indentation tests. The graded ceramic also possesses wear properties that are significantly improved compared with dense, monolithic Si₃N₄ containing 2 vol% YAG additive. The improved wear resistance is attributed solely to the large compressive stress present at the contact surface. A modification of the simple wear model by Lawn and co-workers is used to rationalize the wear results. Results from this work clearly show that the introduction of surface compressive residual stresses can significantly improve the wear resistance of polycrystalline ceramics, which may have important implications for the design of contact-damage-resistant ceramics.